The single-petal method, as its name implies, is used to build a flower petal by petal. Each petal is individually shaped and pleated before being attached to the stem. To construct one of these flowers, first make the appropriate stamen from crepe paper and floral wire and cut the necessary number of petals and leaves from crepe paper. Then shape the petals, and attach them to the stamen with floral tape.
Use 6 petals (get the template below), a fringe stamen, and two elongated leaves. Shape petals to cup inward slightly; roll three of them at the widest point to curve strongly inward. Pleat base of each petal; pinch folds in place. Attach heavily cupped petals to stamen; add remaining petals, overlapping slightly. Attach leaves low on stem.
Use 35 petals (get the template below) and a button stamen. Shape petals to cup inward slightly. Pleat base of each petal; pinch folds in place. Attach to stamen, positioning innermost petals low, with midpoints at stamen's head; raise each subsequent ring of petals slightly. Curl tips of petals inward.
Use five small and seven large petals (get the template below) and a bud stamen. Cup petals at a point just below middle; curl upper edge outward. Pleat base of each petal; pinch folds in place. Attach petals to stamen, first positioning small petals lower on stamen and tightly curled around it; raise each subsequent ring of petals slightly, overlapping petals.
For this technique, a strip of paper cut with a fringe of petals is attached to a stamen, and petals are shaped afterward, sometimes several at a time. First make the stamen and cut petal strips and leaves. Then firmly wrap the strip of petals around the stamen or around itself; secure with floral tape. Practice so the strip doesn't slip, or cut it into shorter lengths and attach in stages. Then attach leaves and shape petals.
Use 36 inches of petals (get the template below), a fringe stamen and one or more teardrop leaves. Attach end of strip to stamen; wind it around, gradually bringing strip higher on stamen. Starting near their bases, curl inner layers of petals tightly inward, several at once. Curl outer petals less tightly.
Use three strips of petals (get the template below), each 12 inches. Tightly pleat bottom edge of one strip, then wrap it firmly around itself, keeping bottom edge aligned. Secure with floral tape. Repeat with other strips. Tape bases of rolled strips to the end of a plain floral wire and to one another, wrapping tape down stem. Pull petals outward to create a dome.
Use 18 inches of petals (get the template below), a button stamen, and two notched leaves. Attach strip to stamen, pleating bottom edge to prevent bunching, and keeping it aligned as you wrap. Cup each petal outward, then curl petals outward, shaping several at a time. Attach leaves near base of stem with tape.
Cut 18-gauge cloth-wrapped floral wire to desired length: 12 inches is a good starting length for a bouquet; 6 works well for a boutonniere.
Clockwise from top left:
Button: Cut 11/2-inch square of crepe paper. Place thumbnail-size wad of cotton in center; push end of wire into cotton. Wrap paper around cotton; twist ends around wire. Secure with floral tape. (Daisy)
Bud: Cut a 3-inch square of crepe paper; fold it into a triangle. Bring far tips in toward center bottom point, slightly overlapping. Hold the tips together; twist. Secure tips to end of wire with floral tape. (Rose)
Pistil: Cut a 1/2-by-6-inch strip of off-white crepe paper. Twist it tightly between your fingers, and tie a knot at one end. Cut three 1/8-by-4-inch strips of heavy red crepe paper; bend each at one end. Attach all strips, off-white in center, to end of wire with floral tape. (Lily)
Floret: Cut 6-by-2-inch strip of crepe paper; fold every 1/2 inch. Cut petals as shown. Wrap around end of wire. Secure with floral tape.
Triple Button: Cut three 1-inch squares of crepe paper; make three wads of cotton the size of a pinky nail. Attach to wire as for #1. Place buttons together, heads staggered; tape together with floral tape.
Fringe: Cut a 6-by-2-inch piece of crepe paper. Make cuts into one long side, about every 1/8 inch, to create a fringe. Roll paper tightly around end of wire. Secure with floral tape. (Tulip, spider mum, dahlia)
Clockwise from top left:
Notched: Position these leaves down the stem a few inches below the base of the flower head, and secure with floral tape. (Daisy)
Teardrop: Cut a few 1/4-inch-deep slits into the sides of each leaf at the tip, spacing them approximately 1/8 inch apart as shown on the template. Give the leaf a slight inward cup, following the shaping technique given for single petals seen here. (Rose)
Standard: Pleat the base of each of these leaves before attaching them. Add a short stem made of 18-gauge cloth-wrapped floral wire in one of two ways: Either attach the leaf to the wire by wrapping floral tape around the base overlapping wire and slightly cupping leaf around stem, or glue wire up center back of leaf with craft glue. (Spider mum)
Grassy: Start with a 2-by-5-inch strip of crepe paper. Fold accordion-style, and place template on top; create a spiky fringe by cutting narrow Vs into one long side of the strip following the template. To attach, place one end of strip on flower head at the base of the flower head, and wrap it around the stamen; secure with floral tape.
Elongated: Fold each leaf in half lengthwise, then pleat its base by pinching. Attach these leaves on the stem a few inches below the base of the flower by wrapping floral tape around the base. (Tulip, lily)
Make the blossoms at right using five to ten continuous petals cut into rounded teardrops; use an 11-inch length of floral wire for the stamen of your choice. About 4 inches down from flower, twist two tiny circles in wire with round-tipped needlenose pliers; these circles grip the card. About 1 inch below that, bend wire out 90 degrees, then into a circular base. To display, cut 2-inch slits into felt draped over table; slip one side of each base into a slit.